Print a track plan at 1:1: tiles, paper and printer settings
Benjamin | TrackDrawer.com · published 17 November 2026
You print a track plan at 1:1 by creating it as a PDF in tiles, printing every page at 100 percent and joining the sheets at the registration marks. The printer setting matters most: "fit to page" shrinks the plan, and then no piece of track fits its outline any more. A ruler on the cutting line tells you in seconds whether the scale is right.
A full-size plan is the best tool between the screen and the baseboard. You lay the track on it and see straight away whether the curve fits, where the turnout goes and whether you can reach the back corner. How to transfer centre lines and fixed points onto the board afterwards is covered in Laying track: from plan to baseboard. This article is about the printing itself.
Step 1: Choose the paper size
TrackDrawer prints the tiles in portrait on A4, A3, A2, A1 or A0. A4 and A3 work on many home printers; A2 to A0 is a job for a copy shop or a plotter. Every page has a 15 mm margin so that printers without borderless printing still catch everything. The usable part of an A4 tile is therefore 180 x 267 mm.
The number of tiles depends on your baseboard size. For a 180 x 90 cm baseboard it looks like this:
| Paper | Usable part per tile | Tiles (columns x rows) | In the free preview |
|---|---|---|---|
| A4 | 180 x 267 mm | 10 x 4 = 40 | 8 |
| A3 | 267 x 390 mm | 7 x 3 = 21 | 5 |
| A2 | 390 x 564 mm | 5 x 2 = 10 | 2 |
| A1 | 564 x 811 mm | 4 x 2 = 8 | 2 |
| A0 | 811 x 1159 mm | 3 x 1 = 3 | 1 |
The larger the paper, the fewer seams. Forty A4 sheets are an evening of cutting and taping; three A0 strips are laid out in ten minutes. For a first test, A4 is plenty.
Step 2: Create the PDF
Under "Output" you choose the paper and create the "PDF 1:1 in tiles". Two switches are worth a look: "Item numbers on the pieces" writes on each track which piece belongs there, and the Märklin grid lays lines at 180 and 360 mm over the plan.
The PDF always starts with an overview on A4. It shows the whole plan with the tile grid and the tile names: rows as letters, columns as numbers, so A1, A2 and so on. Then comes one page per tile. At the top it says which tile it is, at the bottom which tiles join on the left, right, top and bottom. Drawn on it are the baseboard, the free margin as a red dashed line, the roadbed at full width and the track centre line as a dark line.
If you only want an overview, use the "PDF to scale": the whole plan on one landscape page, with the scale in the header and the parts list after it.
Step 3: Print at 100 percent
Open the PDF and choose actual size or 100 percent in the print dialogue. Switch off "fit to page", "shrink oversized pages" and the like. These settings have different names in each program but do the same thing: they make the plan a few percent smaller so that it fits the printable area. On a 180 mm tile, three percent is already more than 5 mm.
Print only the first tile page before you use up all forty sheets.
Step 4: Check the scale
Every tile has a dashed cutting line. It surrounds exactly the usable part, so 180 x 267 mm on A4. Put a ruler against it: if you measure 180 mm, the print is right. If you measure clearly less, the printer has scaled it; go back to step 3.
A second check uses a real piece of track. Lay a straight piece on its outline, on Märklin C track for example the 24188 straight of 188.3 mm. Roadbed and outline must coincide. A millimetre of difference over the length of one piece is paper and toner; more than that is a print setting.
Step 5: Trim and join the tiles
The tiles overlap by 5 mm. This is how you join them:
- Trim one side: cut each tile along the dashed line on the right and at the bottom, and leave the overlap on the left and at the top. That 5 mm strip later slides under the neighbouring tile.
- Lay out by name: the overview shows where each tile goes. Start with A1 in the top left corner.
- Line up the registration marks: every corner of the cutting line has a cross. The crosses of neighbouring tiles sit exactly on top of each other, and then the track lines run on too.
- Tape from behind: a strip of tape on the back keeps the seam flat and leaves the front free for drawing.
Then put the plan on the baseboard and fix it at the corners. Now you can lay the track on it as a trial. If a loop leaves a gap on paper when you close it, read Your layout will not close: a gap of a few millimetres.
Free or with Pro
For free you print a preview: 20 percent of the tiles, rounded up and at least one, namely the ones with the most track. That way you can lay out the station area as a trial and see how the print works. The other tiles appear grey with "Pro" on the overview. With Pro you get all tiles, in every size from A4 to A0. The PDF to scale and the parts list are available without Pro too.
Frequently asked questions
Why is my print a few millimetres too small?
Usually because the printer fitted the plan to the page. Choose 100 percent or actual size in the print dialogue and measure the cutting line again.
Do I need an A3 or larger printer?
No. A4 is enough, it is just more sheets. Larger sizes save seams; for those you send the PDF to a copy shop and say explicitly that it must be printed at actual size.
Can I print only part of the plan?
The tiles are separate pages in the PDF. In the print dialogue you simply select only the pages you need, for example the tiles around a set of turnouts.
Your plan at full size
Create your plan in the track planner or find a ready-made plan in the Railfolio and print the preview on A4. With a real piece of track on it you soon notice whether the plan works as well on the baseboard as on the screen.